Search found 10 matches

by jmhill373
Thu Sep 19, 2019 6:32 pm
Forum: Boxertech
Topic: Final drive rusted onto driveshaft.
Replies: 9
Views: 9534

Re: Final drive rusted onto driveshaft.

Hi Ok I have solved this one so here is how to do it. There isn’t a circlip on the final drive end it should just pull out. Also my bike has a full BMW service history! Clamp the drive shaft in a vice so that the thicker cushdrive is against the jaws acting as a stop to prevent the driveshaft moving...
by jmhill373
Fri Jul 20, 2018 6:50 am
Forum: Boxertech
Topic: Factory Alarm not working
Replies: 4
Views: 5398

Re: Factory Alarm not working

Hi

Opened the alarm up batteries are at 100%?

Any other ideas? could it be the wiring or is the unit kaput?

Regards,

Jon
by jmhill373
Fri Jul 20, 2018 6:48 am
Forum: Boxertech
Topic: Lower stick coils handed?
Replies: 4
Views: 5170

Re: Lower stick coils handed?

Hi Thanks,

I have sent you a PM

I have tried a RH lower coil from a GS it doesn't fit very well but my bike is back to its old self :D

Jon
by jmhill373
Thu Jul 12, 2018 10:20 am
Forum: Boxertech
Topic: Factory Alarm not working
Replies: 4
Views: 5398

Re: Factory Alarm not working

Hi David,

Many thanks, I'll give that a try.

Jon
by jmhill373
Thu Jul 12, 2018 9:18 am
Forum: Boxertech
Topic: Factory Alarm not working
Replies: 4
Views: 5398

Factory Alarm not working

Hi,

My factory fitted R1200S alarm isn't working.

Is it possible for the fob to become out of sync with the alarm unit?

Jon
by jmhill373
Thu Jul 12, 2018 9:15 am
Forum: Boxertech
Topic: Lower stick coils handed?
Replies: 4
Views: 5170

Lower stick coils handed?

Hi, I have got the dreaded rough running of a faulty stick coil. My bike is an 2008 r1200s and has done 29000 miles. I replaced one of the upper coils with a 2hd unit a few years ago. I've bought a new upper coil (Chinese copy) from ebay I've changed it but still have the same intermittent rough run...
by jmhill373
Thu Jul 12, 2018 9:07 am
Forum: Boxertech
Topic: Swing arm bush/bearing replacement
Replies: 2
Views: 4021

Re: Swing arm bush/bearing replacement

Many thanks!
by jmhill373
Thu Jul 12, 2018 9:06 am
Forum: Boxertech
Topic: Fork Seals
Replies: 6
Views: 5737

Re: Fork Seals

I changed mine a couple of weeks ago.

An easier way is to undo the pinch bolt on the top yoke and pull the upper fork tube up through it.

Its a bit fiddly but you can remove the seal from the lower fork tube in-situ and then put it all back together.

Regards,

Jon
by jmhill373
Wed Jun 27, 2018 7:23 pm
Forum: Boxertech
Topic: Swing arm bush/bearing replacement
Replies: 2
Views: 4021

Swing arm bush/bearing replacement

Hi,

My R1200S passed it's MOT today after two years of standing idle. I've had an advisory that there is some play in the rear swinging arm.

How do I replace the bearings bushes, is it a big job?

Regards,

Jon
by jmhill373
Mon Jun 18, 2018 5:27 pm
Forum: Boxertech
Topic: Holey brake pistons and bobbins
Replies: 4
Views: 5084

Re: Holey brake pistons and bobbins

Hi

Thanks for the advice I’ve bought a good condition used pair for £100 so will keep the originals as spares. Hopefully will be MOT’d and back on the road next week.

Thanks again,

Jon

Go to advanced search