R1100S Output Shaft Seal Woes

Got a technical query? Found another 0.02bhp? Ask/tell the world.

Moderators: Gromit, Paul, slparry

weaselonastick
Posts: 21
Joined: Thu Dec 26, 2013 5:13 pm
Location: Edmonton, AB Canada

R1100S Output Shaft Seal Woes

Postby weaselonastick » Sun Jul 16, 2017 1:19 am

Folks,
I've posted on the Pelican forum, but wanted to make sure I got a Global perspective on my issue.

I've replaced the transmission output shaft seal on my R1100S at least 4 times in the last two years. After the last failure, I was fed up, and completely dismantled the transmission and replaced the output shaft bearings and the seal on the workbench (rather than on the bike like the I've done in the past). I did that a few weeks ago, and the bikes has sat idle since then (not even started). I checked it today... and the seal is leaking. Just to be clear... a new OEM seal was installed 3 weeks ago, and the transmission filled with oil; the transmission has not done a single revolution since then, and transmission oil is leaking around the shaft.

Bike has about 27K miles. 2004 model.

I thought that in each case I was careful with the new seal, making sure to protect it from scoring when sliding it over the output shaft. Particularly with the transmission on the bench.

On some of my original searches to replace the seal I seem to remember two possible causes for failure... a) worn bearings (causing the shaft to wobble) and b) something wrong with the new OEM supplied seals. The location of the seal in relation to the shaft was also critical, but looking at the shaft (out of the transmission), I'm not sure that is a valid point... the shaft is the same diameter from the chamfer behind the splines all the way into the transmission (directly under the seal location).

So I've replaced the output shaft bearings, and used multiple OEM seals.

So I'm at wits end.

I'm looking for any suggestion, no matter how significant or insignificant to solve this issue.

Thanks in advance.
Mike
2004 BMW R1100S
1982 Piaggio PX125E
1972 Kawasaki H1B
1970 Yamaha XS1
1970 Yamaha R5
1970 Honda CB750K0
1965 Ducati Sebring

Jeff Highland
Posts: 87
Joined: Thu Jan 12, 2017 10:03 pm

Re: R1100S Output Shaft Seal Woes

Postby Jeff Highland » Sun Jul 16, 2017 2:56 am

A scratch on the shaft?
A seal is only as good as the surface it mates to.

weaselonastick
Posts: 21
Joined: Thu Dec 26, 2013 5:13 pm
Location: Edmonton, AB Canada

Re: R1100S Output Shaft Seal Woes

Postby weaselonastick » Sun Jul 16, 2017 3:01 am

Jeff,
Nothing that can be seen or felt on the shaft. We ran 600 grit wet-dry on the shaft (1-2 light passes) just to make sure.
Mike
2004 BMW R1100S

1982 Piaggio PX125E

1972 Kawasaki H1B

1970 Yamaha XS1

1970 Yamaha R5

1970 Honda CB750K0

1965 Ducati Sebring

Jeff Highland
Posts: 87
Joined: Thu Jan 12, 2017 10:03 pm

Re: R1100S Output Shaft Seal Woes

Postby Jeff Highland » Sun Jul 16, 2017 3:34 am

You are sure it's leaking around the shaft not the outside of the seal to the housing?

weaselonastick
Posts: 21
Joined: Thu Dec 26, 2013 5:13 pm
Location: Edmonton, AB Canada

Re: R1100S Output Shaft Seal Woes

Postby weaselonastick » Sun Jul 16, 2017 3:36 am

Absolutely. I can see the oil forming a ring around the shaft, then dripping/running down the seal face to the transmission housing.
2004 BMW R1100S

1982 Piaggio PX125E

1972 Kawasaki H1B

1970 Yamaha XS1

1970 Yamaha R5

1970 Honda CB750K0

1965 Ducati Sebring

Jeff Highland
Posts: 87
Joined: Thu Jan 12, 2017 10:03 pm

Re: R1100S Output Shaft Seal Woes

Postby Jeff Highland » Sun Jul 16, 2017 3:41 am

Sorry I can't suggest anything else, good luck

Jeff Highland
Posts: 87
Joined: Thu Jan 12, 2017 10:03 pm

Re: R1100S Output Shaft Seal Woes

Postby Jeff Highland » Sun Jul 16, 2017 9:06 am

Unless the shaft for some reason is undersize

User avatar
nab 301
Member
Posts: 2374
Joined: Sat Dec 04, 2004 6:41 pm
Location: Dublin Ireland

Re: R1100S Output Shaft Seal Woes

Postby nab 301 » Wed Jul 19, 2017 6:49 pm

you've probably found this post , viewtopic.php?f=4&t=16772&hilit=output+seal&start=15
Maybe try a seal from a bearing supplier.
Some seal sizes listed at the end of this post
viewtopic.php?t=10343&postdays=0&postorder=asc&start=15
_________________
Nigel

Keep smiling, it makes people wonder what you've been up to!
1999 R1100s (mandarin) '
2018 DL 250V Strom
2019 CB125F Honda.
MZ301 Saxon Fun ( currently retired)
'03 Bullet 65 project..

weaselonastick
Posts: 21
Joined: Thu Dec 26, 2013 5:13 pm
Location: Edmonton, AB Canada

Re: R1100S Output Shaft Seal Woes

Postby weaselonastick » Thu Jul 20, 2017 2:50 am

I think I've got it sorted, based on some feedback from the BMWMOA forum.
In every case, I've replaced the seal while the transmission was still on the bike AND driving the seal all the way to the back of the housing (against the bearing within the transmission).
With the trans on the bike, you can't see the oil hole on the shaft.
Driving the seal hard against the bearing puts the seal right over the oil hole.
And that's why the location of the seal in the housing is important, but I believe it's not the best design.
The housing depth is approximately 7.5-8mm, while the seal is 6mm deep. That basically gives a 1.5-2mm tolerance on the location of the seal.
The oil hole on the shaft appears to be about 1-1.5mm from the bearing face.
The seal ring(?) on the seal itself appears to be about 0.5-1mm from the rear of the seal (or 0.5-1mm from the bearing if you drive the seal against it).
So you really don't have much flexibility on the location of the seal. On my bike, the seal must be located flush to the face of the transmission housing, not seated against the bearing.
From what I've read, most people craft some kind of seal driver with a stop, so the the seal only goes a certain distance into the housing.
I don't have a lathe to make the seal driver, so I made a large washer from PVC that sits against the bearing, that you can drive the seal up against and it will stop.
The washer is 40mm OD, 2mm thick and 30mm ID. This still allows oil to come out of the oil hole on the shaft to lubricate the seal, and makes a solid stop for the seal.
I haven't ridden the bike yet, but I did spin the shaft a pile of times... 48 hours later and no leak. I'll report in after I've got the bike back together and done a few miles.

So it appears to be operator error, and not the seal.

Nab301.. I sourced a 25x40x7 seal from a local hydraulics shop and tried it on one of my earlier attempts. The 7mm width moved the seal ring further away from the bearing, but not enough to clear the oil hole IF you seat the seal against the bearing.

Thanks to all who've offered support.

Mike
2004 BMW R1100S

1982 Piaggio PX125E

1972 Kawasaki H1B

1970 Yamaha XS1

1970 Yamaha R5

1970 Honda CB750K0

1965 Ducati Sebring

weaselonastick
Posts: 21
Joined: Thu Dec 26, 2013 5:13 pm
Location: Edmonton, AB Canada

Re: R1100S Output Shaft Seal Woes

Postby weaselonastick » Thu Jul 20, 2017 7:24 pm

I was advised that in placing the washer over the bearing, I've likely blocked the oil path back from the seal through the bearing into the gearbox... so I'll be removing the spacer this weekend.
2004 BMW R1100S

1982 Piaggio PX125E

1972 Kawasaki H1B

1970 Yamaha XS1

1970 Yamaha R5

1970 Honda CB750K0

1965 Ducati Sebring


Return to “Boxertech”

Who is online

Users browsing this forum: No registered users and 48 guests