motor cut out!!!!

Got a technical query? Found another 0.02bhp? Ask/tell the world.

Moderators: Gromit, Paul, slparry

Pheasant Plucker
Posts: 45
Joined: Wed Feb 15, 2006 6:55 pm
Location: Darkest Dorset.

motor cut out!!!!

Postby Pheasant Plucker » Tue Apr 04, 2006 11:59 am

Only had the 1100s a few months so I dont really know my way around the bike yet.
So, the sun came out ,took the bike for a spin, after ten miles the engine cut out.
I tried to start it, she fired once then nothing but after getting a tzxi home and returning with my pick-up the bloody thing started ..............
Is there a common electrical fault with these bikes that everyone exept me knows about?

Hope someone may have an answer.
Thanks, Paul.

User avatar
Harry
Member
Posts: 752
Joined: Fri Feb 20, 2004 10:08 am
Location: Home of the Saints

Postby Harry » Tue Apr 04, 2006 3:40 pm

Yup, check for chaffing where the wires go over the frame rails on the LH side under the faring.
Pauls got some pics. He'll probablybe along in a bit with the right link....

Harry.

User avatar
gus
Member
Posts: 2418
Joined: Thu Feb 19, 2004 5:10 pm
Location: birmingham

Postby gus » Tue Apr 04, 2006 5:04 pm

Hi
Could be electrical as harry has suggested.Sure you didnt flood it when trying to restart?Sidestand switch can also be the culprit.Funny it started after you returned to it.
gus

cc mac
Posts: 494
Joined: Sun Aug 21, 2005 9:30 pm
Location: wirral. north west england

Postby cc mac » Tue Apr 04, 2006 9:12 pm

If the motor turns over and you can hear the fuel pump kick in when you turn it on, it might be the halls sensor. It usually shows up when the motor is warm. After a couple of cut outs it'll stop altogether. Cost me about two hundred at a BMW dealer. Good luck.
Watching you Focker!

Pheasant Plucker
Posts: 45
Joined: Wed Feb 15, 2006 6:55 pm
Location: Darkest Dorset.

Postby Pheasant Plucker » Wed Apr 05, 2006 10:18 pm

I've had the bike running in the shed tonight and you would not think there is anything wrong with it at all.
I tried the side stand when it stopped first.
Thanks for all your help.
These modern bikes are a bit of an unknown to me.
Never had a fuel injected bike with all these sensors etc.
I will ride around close to home this weekend and see what happens.

p.s. got a taxi home when the bike stopped.
picked the bike up on my toyota and blew the head gasket and rad on the way back!!!
S**T really does happen!!

User avatar
Jason M
Posts: 1404
Joined: Wed Feb 18, 2004 7:56 am
Location: southampton

Postby Jason M » Thu Apr 06, 2006 7:20 am

Pheasant Plucker wrote:I've had the bike running in the shed tonight and you would not think there is anything wrong with it at all.
I tried the side stand when it stopped first.
Thanks for all your help.
These modern bikes are a bit of an unknown to me.
Never had a fuel injected bike with all these sensors etc.
I will ride around close to home this weekend and see what happens.

p.s. got a taxi home when the bike stopped.
picked the bike up on my toyota and blew the head gasket and rad on the way back!!!
S**T really does happen!!


How old is the bike and how many miles has it done? Mine kept doing this (usually when filtering through traffic on the motorway). It turned out to be the wire from the ignition to the fusebox (that gets constantly bent when steering) had developed a break/chaff. Cost me about £20 for a 2nd hand one from Motorworks.

Jason

Pheasant Plucker
Posts: 45
Joined: Wed Feb 15, 2006 6:55 pm
Location: Darkest Dorset.

Postby Pheasant Plucker » Thu Apr 06, 2006 10:03 pm

Thanks Jason, I'll check this out as it sounds so much cheaper than a hall sensor.

User avatar
Jason M
Posts: 1404
Joined: Wed Feb 18, 2004 7:56 am
Location: southampton

Postby Jason M » Fri Apr 07, 2006 7:01 am

Pheasant Plucker wrote:Thanks Jason, I'll check this out as it sounds so much cheaper than a hall sensor.


The Halls sensor is just a little thing that sits on a plate behind the alternator belt wheel on the end of the crank - you will be able to pick up a 2nd hand one no probs if it's that, and they're dead easy to replace. I think that if the problem is intermittent though it's less likely to be the sensor (hopefully)

Jason

Pheasant Plucker
Posts: 45
Joined: Wed Feb 15, 2006 6:55 pm
Location: Darkest Dorset.

Postby Pheasant Plucker » Tue Apr 11, 2006 4:36 pm

I have run the bike for about 20 minutes in the shed tonight, I've moved the wires back and forth but not found a fault.
I cant imagine it could be the ignition trigger because it just keeps running O.K.
I will have to go for a longer ride and if there is a problem perhaps Carole Nash or those nice people in the RAC may bring me home.
I must get to the bottom of the problem as I intend to ride to the south of France later in the year.

Thanks for all your suggestions, Paul.[/quote]

Neil178
Posts: 761
Joined: Sun Aug 29, 2004 11:24 pm
Location: East Mids

Postby Neil178 » Tue Apr 11, 2006 8:27 pm

20 minutes? Don't forget it's aircooled! :?

User avatar
oyster
Posts: 1236
Joined: Fri Jul 02, 2004 1:03 pm
Location: retirementland kent

Postby oyster » Thu Apr 13, 2006 6:22 pm

Bob aka Boxerdog posted a photo last year of the weak wires under the ignition switch, cant remember the title of the thread. The other favourite chafe point is under the left fairing cover around the long fuse box.
Oyster. 1999 R1100S. Almost original.

User avatar
Paul
Wanna buy a sticker mister?
Posts: 2866
Joined: Mon Feb 16, 2004 8:44 pm
Location: Boxertrix Towers, Norfolk
Contact:

Postby Paul » Fri Apr 14, 2006 7:08 am

The "Search" function (top right on the forum pages) is your friend.

Boxerdog's post is here.

My post about chaffed wires is here.

Paul
You really need only two tools: WD-40 and duct tape. If it doesn't move and it should, use WD-40. If it moves and shouldn't, use the tape.

Pheasant Plucker
Posts: 45
Joined: Wed Feb 15, 2006 6:55 pm
Location: Darkest Dorset.

motor cut!!!!

Postby Pheasant Plucker » Sat Apr 15, 2006 2:22 pm

You meet the nicest people on a Honda was the seventies add.............
They must all ride 1100s's now !!!!!!!

Thanks for all your help. Problem not sorted yet but its raining so I'm off to my shed.


Return to “Boxertech”

Who is online

Users browsing this forum: No registered users and 37 guests